[nylug-talk] (no subject)

Adam Vazquez adamvaz at palm.net
Wed May 21 11:14:01 EDT 2003 

Sorry for the tardiness. I had to take care of family issues. Attached is all
the information you gents requested. BTW, this is my first time doing this.

Thanks in advance.

Adam


____________________________________________________________________
This message was sent from my Palm wireless email account.
-------------- next part --------------
ifconfig -a:
eth0      Link encap:Ethernet  HWaddr 00:06:29:52:AE:2D
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:11 Base address:0x4000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:40 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2608 (2.5 Kb)  TX bytes:2608 (2.5 Kb)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
dmesg:
Linux version 2.4.20-4GB (root at Pentium.suse.de) (gcc version 3.3 20030226 (prerelease) (SuSE Linux)) #1 Mon Mar 17 17:54:44 UTC 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000013ff8000 (usable)
 BIOS-e820: 0000000013ff8000 - 0000000014000000 (ACPI NVS)
Scanning bios EBDA for MXT signature
0MB HIGHMEM available.
319MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 81912
zone(0): 4096 pages.
zone(1): 77816 pages.
zone(2): 0 pages.
Building zonelist for node : 0
Kernel command line: root=/dev/hda11 vga=0x317  ide=nodma apm=off acpi=off splash=silent splash=silent
ide_setup: ide=nodma : Prevented DMA
bootsplash: silent mode.
bootsplash: silent mode.
Initializing CPU#0
Detected 299.348 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 596.37 BogoMIPS
Memory: 320056k/327648k available (1569k kernel code, 7204k reserved, 574k data, 160k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU:             Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch at atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030228
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xf0484, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled on user request.
mxt_scan_bios: enter
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
kinoded started
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 20478
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0x40000000, mapped to 0xd480d000, size 4096k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:4da0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... silenjpeg size 30311 bytes, found (1024x768, 23130 bytes, v3).
Got silent jpeg.
Got silent jpeg.
Console: switching to colour frame buffer device 118x38
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x2020-0x2027, BIOS settings: hda:DMA, hdb:DMA
hda: IC25N030ATCS04-0, ATA DISK drive
hdb: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB) w/1768KiB Cache, CHS=3876/240/63
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 >
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 475k freed
VFS: Mounted root (ext2 filesystem).
reiserfs: found format "3.6" with standard journal
reiserfs: enabling write barrier flush mode
reiserfs: using ordered data mode
reiserfs: checking transaction log (ide0(3,11)) for (ide0(3,11))
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 160k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding Swap: 657680k swap-space (priority 42)
MSDOS FS: IO charset iso8859-1
MSDOS FS: IO charset iso8859-1
MSDOS FS: IO charset iso8859-1
MSDOS FS: IO charset iso8859-1
MSDOS FS: IO charset iso8859-1
NTFS driver 2.1.1a [Flags: R/O MODULE].
NTFS volume version 3.1.
raw1394: /dev/raw1394 device initialized
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:24:43 Mar 17 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x2000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
mice: PS/2 mouse device common for all mice
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:11.0
PCI: Sharing IRQ 11 with 00:11.1
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 11 for device 00:11.1
PCI: Sharing IRQ 11 with 00:11.0
PCI: Sharing IRQ 11 with 01:00.0
Yenta IRQ list 0698, PCI irq11
Socket status: 30000020
Yenta IRQ list 0698, PCI irq11
Socket status: 30000020
cs: cb_alloc(bus 2): vendor 0x115d, device 0x0003
PCI: Enabling device 02:00.0 (0000 -> 0003)
cs: cb_alloc(bus 3): vendor 0x1033, device 0x0035
PCI: Enabling device 03:00.0 (0000 -> 0002)
PCI: Enabling device 03:00.1 (0000 -> 0002)
PCI: Enabling device 03:00.2 (0000 -> 0002)
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x03e0-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0100-0x03af: excluding 0x100-0x107 0x220-0x22f 0x250-0x257 0x260-0x267 0x330-0x337 0x378-0x37f 0x388-0x38f
cs: IO port probe 0x0a00-0x0aff: clean.
PCI: Setting latency timer of device 02:00.0 to 64
eth0: Xircom cardbus revision 3 at irq 11
PCI: Setting latency timer of device 03:00.0 to 64
usb-ohci.c: USB OHCI at membase 0xd4d5a000, IRQ 11
usb-ohci.c: usb-03:00.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: new USB device 03:00.0-1, assigned address 2
spurious 8259A interrupt: IRQ7.
usb.c: USB device 2 (vend/prod 0x2821/0x5001) is not claimed by any active driver.
PCI: Setting latency timer of device 03:00.1 to 64
usb-ohci.c: USB OHCI at membase 0xd4d5c000, IRQ 11
usb-ohci.c: usb-03:00.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
hub.c: new USB device 03:00.0-2, assigned address 3
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB device not accepting new address=3 (error=-110)
hub.c: new USB device 03:00.0-2, assigned address 4
usb.c: USB device not accepting new address=4 (error=-110)
ehci-hcd 03:00.2: PCI device 1033:00e0
ehci-hcd 03:00.2: irq 11, pci mem d4d5e000
usb.c: new USB bus registered, assigned bus number 4
PCI: 03:00.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 03:00.2 PCI cache line size corrected to 32.
ehci-hcd 03:00.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22
usb.c: USB disconnect on device 03:00.0-1 address 2
hub.c: USB hub found
hub.c: 5 ports detected
hub.c: new USB device 03:00.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x2821/0x5001) is not claimed by any active driver.
hub.c: new USB device 03:00.2-3, assigned address 3
usb.c: USB device not accepting new address=3 (error=-71)
hub.c: new USB device 03:00.2-3, assigned address 4
usb.c: USB device not accepting new address=4 (error=-71)
Got silent jpeg.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
Got silent jpeg.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
  Vendor: TDK       Model: CDRW481648UED     Rev: 1.2
  Type:   CD-ROM                             ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux video capture interface: v1.00
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -32

lspci -v:

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:11.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
00:11.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro AGP-133 (rev dc)
02:00.0 Ethernet controller: Xircom Cardbus Ethernet 10/100 (rev 03)
03:00.0 USB Controller: NEC Corporation USB (rev 41)
03:00.1 USB Controller: NEC Corporation USB (rev 41)
03:00.2 USB Controller: NEC Corporation USB 2.0 (rev 02)
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
	Subsystem: Compaq Computer Corporation Armada 1750 Laptop System Chipset
	Flags: bus master, medium devsel, latency 64
	Memory at 50000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 1.0

00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
	Flags: 66Mhz, medium devsel
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: 40000000-410fffff

00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
	Flags: bus master, medium devsel, latency 0

00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
	Flags: bus master, medium devsel, latency 64
	I/O ports at 2020 [size=16]

00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
	Flags: bus master, medium devsel, latency 64, IRQ 11
	I/O ports at 2000 [size=32]

00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
	Flags: medium devsel, IRQ 9

00:11.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device b121
	Flags: bus master, medium devsel, latency 168, IRQ 11
	Memory at 7fffe000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=176
	Memory window 0: 14000000-143ff000 (prefetchable)
	Memory window 1: 14400000-147ff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	16-bit legacy interface ports at 0001

00:11.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device b121
	Flags: bus master, medium devsel, latency 168, IRQ 11
	Memory at 7ffff000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=176
	Memory window 0: 14800000-14bff000 (prefetchable)
	Memory window 1: 14c00000-14fff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	16-bit legacy interface ports at 0001

01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro AGP-133 (rev dc) (prog-if 00 [VGA])
	Subsystem: Compaq Computer Corporation 3D Rage LT Pro (Compaq Armada 1750)
	Flags: bus master, stepping, medium devsel, latency 66, IRQ 11
	Memory at 40000000 (32-bit, non-prefetchable) [size=16M]
	I/O ports at 1000 [size=256]
	Memory at 41000000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
	Capabilities: [5c] Power Management version 1

02:00.0 Ethernet controller: Xircom Cardbus Ethernet 10/100 (rev 03)
	Subsystem: IBM 10/100 EtherJet Cardbus Adapter
	Flags: bus master, medium devsel, latency 64, IRQ 11
	I/O ports at 4000 [size=128]
	Memory at 14400000 (32-bit, non-prefetchable) [size=2K]
	Memory at 14400800 (32-bit, non-prefetchable) [size=2K]
	Expansion ROM at 14000000 [size=16K]
	Capabilities: [dc] Power Management version 1

03:00.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
	Subsystem: Adaptec: Unknown device 1235
	Flags: bus master, medium devsel, latency 64, IRQ 11
	Memory at 14c00000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

03:00.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
	Subsystem: Adaptec: Unknown device 1235
	Flags: bus master, medium devsel, latency 64, IRQ 11
	Memory at 14c01000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

03:00.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
	Subsystem: Adaptec: Unknown device 12e0
	Flags: bus master, medium devsel, latency 68, IRQ 11
	Memory at 14c02000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [40] Power Management version 2

More information about the nylug-talk mailing list